Instrumentation & Controls Engineer
- Location: Kansas City
- Salary: Market related
As an I&C engineer, work with a team of I&C engineers and designers, and other disciplines, to perform detail engineering, including front-end planning work, develop I&C quantities and cost estimation, conduct conceptual studies, perform technical quality reviews, attend Factory Acceptance Testing (FAT), and support construction & commissioning activities . Work under a direct supervision of an I&C lead or work independently on smaller projects or standalone activities.
Requirements:
**this is a 6 month contract to direct hire opportunity100% remote- work from home anywhere within the United States**NO sponsorship available! Only US based candidates apply! Overview:As a Senior Protection & Control Engineer, you will be responsible for designing and implementing protection and control engineering activities for high voltage substation and transmission projects. You will utilize your knowledge of protective relaying and control systems to contribute to EPC substation and transmission projects.Responsibilities:• Perform analysis and design of Protection Systems for HV substation/ and FACTS • Develop substation relaying & metering diagrams (i.e. Single line/A.C./D.C. schematic diagrams) • Develop the substation communication and network diagram • Prepare specification & Bill of Material for Protection/Control/Metering/RTU/ Communication Panels • Develop Protection and Control Panel layouts. • Develop Protection and Control Panel wiring diagrams. • Develop Cable Schedule for Substation. • Perform Factory Acceptance Test for Protection and Control Panels. • Perform reviews of work performed by others • Work closely with other engineering and design team members to coordinate overall design package and requirements • Perform relay coordination study and develop the relay settings file • Coordinate with supplier and contractors • Flexibility to travel locally and internationally to customer meetings and project sites, with an approximate travel of 25%.Qualifications:• Bachelor's degree in Electrical Engineering with a power systems emphasis from an ABET-accredited engineering program; Master's degree preferred. • 8 years or more of experience with a focus on protection/control/communications design for high voltage substations. • Experience in Communication Network Technologies • Experience in Communication protocols such as IEC61850, DNP, Modbus, … • Experience in writing and providing support documentation for relay calculations. • Knowledge on ANSI standards, IEC standards knowledge is a plus. • Experience with various vendor protective relay equipment typically used in substation. protection, including SEL, Siemens, GE. • Familiarity with Auto-CAD or Micro-Station. • Good communication skills. • Professional Engineering license is preferred. • Applicants must be legally authorized for employment in the United States without need for current or future employer-sponsored work authorization. Siemens Energy employees with current visa sponsorship may be eligible for internal transfers.
Specific Skill Sets/Notes: Background must be civil/structural in either industrial/processing plant, O&G, chemical wastewaterMust have on site field experience from the ground up - experience on construction site/preconstructionMust have working on vertically built construction plantsMin 5 years of field eng experienceNo commercial, residential, or building
Summary The Senior Electrical Engineer I&C will provide Instrumentation and Controls (I&C) and Electrical engineering supports to proposal and contract project operation across Boiler, Selective Catalytic Reduction System (SCR), Air Quality Control Systems (AQCS), Wastewater Spray Dryer (WSD), Flue Gas Desulfurization Systems (FGD), Turbine and After Market Service areas. These include generating documents and/or furnishing consultation in engineering calculations and analysis. I & C equipment specifications, technical evaluation, analog and digital control logic diagrams, combustion control system (CCS) & burner management system (BMS) philosophy, process control and alarm set?point list, analytical instruments, loop diagrams, Piping and Instrumentation Diagrams (P&ID), process flow diagrams (PFDs) review, Instrument List, IO List, and ISA format Data Sheets, etc. Electrical equipment specifications, technical evaluation, cable block diagrams, electrical control schematics, interconnection wiring diagrams, one-line diagrams, electrical load list, electrical area classification, and P&IDs & PFDs review. Excellent understanding and knowledge of I&C / Electrical Engineering for power plant environment. Must have a thorough understanding of Codes and Standards related to Power Plant design and installation. Essential Duties & ResponsibilitiesEssential duties and responsibilities include, but are not limited to the following: Develops major Instrumentation and Controls engineering specifications, bid evaluations, and vendor document/drawing reviews for equipment (i.e., Distributed Control System (DCS), Programmable Logic Controller (PLC), CEMS/NOx Monitoring System, Analyzers, Vibration Monitoring System, Fabric Filter Cleaning Control System, Transmitters, Thermocouples, Control Valves, etc.Prepares and reviews engineering calculations, P&IDs, control system narratives and control system architecture, operator interface layout, instrument connection and installation details, location drawings and technical specificationsGenerates DCS Graphic drawings and control logic diagram using SAMA/ISA format for BMS/CCS controls for Boiler and Burners, AQCS, SCR, WSD, FGD, etc. Develops major electrical engineering specifications, bid evaluations, and vendor drawings reviews for equipment (i.e. Medium & Low Voltage Motors (per NEMA MG1), Power Transformers, Switchgear, Motor Control Centers, UPS and VFD Systems, and Pre?Engineered Power Distribution Centers (PDC), and Equipment Layout. etc.Prepares and reviews engineering calculations, one?line diagrams, schematics, block diagrams, wiring diagrams, load list, hazardous area classification (per NFPA 496 & 497), cable schedules, cable tray routings, lighting layouts, panel schedules, grounding layouts, heat tracing, lightning protection layouts, and other electrical layout drawings and specifications as requiredEnsures that I&C / Electrical design & engineering deliverables are delivered per contract specifications, and within budget and schedule as lead engineer, if assignedReviews I&C / Electrical related documents to mechanical, electrical and process equipment technical specifications and vendor drawings of equipment manufacturers or subcontractor’s and prepares comments and recommendationsCoordinates all I&C / Electrical engineering interfaces with other discipline and client as lead engineer, if assignedPrepares I&C / Electrical engineering work plans/progress report and monitor man?hours as lead engineerEnsures work products meet all applicable local and industry codes, standards and regulatory guides specifically NFPA, NEMA, ASME, ISA, etc.Able to review and understand DCS and PLC configuration drawingsAble to support and execute multiple proposal and contract as project discipline engineer with minimum supervisionPerforms I&C / Electrical related equipment inspection FAT Conducts field survey as deemed required Other Duties & Responsibilities Provide supports in developing I&C / Electrical engineering standards and practicesPossess excellent analytical, decision making, planning and organization skillsMust possess excellent leadership skills with the ability to lead others, provide coaching, development and mentoring of subordinatesAbility to travel both within the USA and to other countries, as deemed necessaryFoster a teamwork environmentCommunicate effectively with all levels of employeesAbility to work independently and with othersContinuously seek ways to improve processes to reduce man?hoursOrganize, maintain and control the status of electrical documents & drawings in PWMaintain the highest degree of honesty and integrity at all times Knowledge, Skills, & EducationTo perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. Education and/or Experience: Must have a Bachelor's degree (BA) in Electrical or Mechanical Engineering from a four?year accredited college or university. Candidate shall have a minimum fifteen (15) years’ experience in Instrumentation & Controls / Electrical engineering and design. Post?graduate education is desirable and will be credited as working experience. Excellent understanding and knowledge of industry codes and standards (ANSI/ISA?5.1, NFPA/NEC, IEEE, NEMA) as they relate to the Power Plant. Candidate shall have strong leadership, communication and presentation skills.Language Skills: Candidate must be fluent in English. Strong verbal and written communication skills and interpersonal skills. Must be able to interact and communicate well with individuals in all areas of the company.Mathematical Skills: Candidate must possess the necessary mathematical skills required to perform the work and responsibilities described herein.Reasoning Ability: Ability to exercise good judgment and make sound engineering decisions. Ability to interpret an extensive variety of technical instructions in mathematical or schematic form. Computer Skills: Candidate must literate in using common MS Office software including Word, Excel, Outlook, PowerPoint and Access. Knowledge of graphics, technical diagrams, flow charts, etc.
Position of: Electrical, Instrumentation & Control Manager Scope of Responsibility includes: - • Establishing electrical operation concept, schematic drawings for HV panels, LV MCC & LV DB’s from single line diagram • Good understanding of 66/11kv, 115/11kv, 22/11kv switchgears, control panel and metering panels • Reviewing of offers/drawings for technical compliance, preparation of instrumentation I/O list, cable sizing & termination schedule preparation. Co-ordination with suppliers on design approvals and FAT & SAT • Supervision of installation, erection, testing and commissioning sub-contractors. Co-ordinate with customers to make changes related with approval drawings. • Pre-commissioning testing of various protection relays of Generator, Transformer, Motor & Feeder Protection of ABB, Schneider, Areva, GE, Reyrolle, Siemens make with following functions. • Trouble shooting and maintenance of all kinds of field instruments which are related to DCS & SCADA system • Provides technical, trouble shooting and maintenance support to all electrical equipment and instrumentation, including low/medium/high voltage substations, switchgear, transformers, motors, distribution systems and associated protection and support equipment. • Testing of Current, Voltage & Power transformers, MV/HV/LV circuit breakers, and Control & Protections schemes with complicated interlocking schemes. • Develop engineering capabilities and work with sales team on project proposal and bidding • Preferably with knowledge in Diesel Generator, Control Panel modification, commissioning and testing. Knowledge in Water Treatment System, Boiler, Turbine, Fuel Handling System, Fuel Preparation System is an added advantage. Requirements • Degree in Science in electrical engineering with emphasis on power systems • Min. 5 years of working experience in renewables, power generation, power systems design or similar field. • PE Certificate is an added advantage • Ability to perform detail-oriented, critical reviews of technical documentation • Ability to work in a fast-paced start-up environment • Strong analytical and trouble shooting skills • Ability to write technical reports in English and proficient in MS Office • Quality, Health, Safety and Environment (QHSE) mindset • Travelling/Site stationed is required Interested applicants please send CV to krystal.kow@spencer-ogden.com
Responsibilities Assist process engineering design and coordinate process engineering deliverables with Engineering firm Including, but not limited to: Review vendor equipment approval drawings with focus on interface management between vendorsReview/approve PIDs generatedReview/approve PFDs generatedReview/approve Area Process Narratives/Functional descriptionsReview/approve Equipment specificationsReview/Approve Instrumentation specificationsReview/approve project Basis of Technical DesignReview/approve mass and energy balancesPerform project engineering role with focus on schedule and on facilitating clear communication between the various stakeholders on technical barriers to design advancement.Support construction efforts by answering technical questions and providing quality control oversight on installation and startupAssist with equipment layout developmentProvide technical assistance to procurement and project management with equipment bidding process, including package documentation, bidding, Total Cost of Ownership (TCO)s and bid comparisons. Generate project mass and energy balancesReview and provide feedback on equipment, line, valve, specialty item and instrumentation lists generated by Engineering firm.Ensure project compliance with engineering and equipment standardsApply process safety management (PSM) experience to assist with items such as management of change (MOC) and pre-start up safety reviews (PSSR).Interface effectively with commercial, safety, accounting, legal, environmental, engineering, QA/QC, process safety management, and procurement to assist with project needs.Develop plans for commissioning/start-up and assist in executing same. Education/Experience/Skills Required Bachelor’s degree in Engineering or applicable related field.5 to 10 year total industry experienceMinimum of 5 years experience with field work or operations or constructionMinimum of 5 years experience working with Process Safety principlesExperienced in using TEAMS, Microsoft Word, Microsoft Excel, Visio and PowerPointExperienced in using Navisworks 3D viewing softwareBuilds Shared Vision
The ideal candidate for Senior Electrical Engineer will be responsible as the Technical Support Engineer to facilitate asset reliability and ensures uptime of the vessels; in line with the Company's key business goal. Provide drilling fleet technical supportAssist and lead on technical downtime issuesLiaise with OEM'sInvolved with annual equipment inspectionReview vendor quotations and costings for major equipment repair. Prepare overhaul work-scope for major equipment to ensure OEM correct and accurate pricings on repairs and overhaulsPrepare repair work-scope for capital equipment (5 yearly)Regularly review, development and updating of the planned maintenance system (Star) for electrical equipmentTravel offshore to assist in technical problem solving, repairs & troubleshooting as requiredAssist with annual budget preparation for capital equipment expendituresAssist with and ensure compliance of TMOC procedureAttend equipment D&I/commissioning at vendor facilityAssist with client related technical issuesCarry out rig internal technical auditsAssist Projects/Newbuilds EngineersAssist HOD with the design and implementation of troubleshooting guidesParticipate in duty phone roster system for technical issues outside office hoursBe familiar with all systems, directives and procedures and actively participate in the implementationBe familiar with all electrical rig systems and controls fleet wideBe prepared to travel worldwide at short notice as and when required Candidate should fulfil the following: Preferably a Degree in Engineering (Hons) in Electrical & ElectronicsMinimum 10 years of experience holding the role of technical support and/or project engineering in O&G industryTrained in the following: LTI Driller/ Draw works Control Course; LTI Top Drive Control Course; Advance Siemens PLC STEP 7 Programming Course; Siemens & ABB VFD Course; Siemens PLC STEP 7 Programming Course; TDS- 8SA Top Drive Course; C++ Programming; MD Totco Drilling Instrumentation Course; Ex Certified; NOV Amphion Control System; HVAC CertificateExperience in offshore drilling or upstream industry with hands-on experience in drilling systems is a plusHighly skilled and efficient trouble shooter
Job Summary Under minimal supervision, responsible for support of NERC CIP compliance activities associated substation relaying and associated equipment.This position ensures high quality of the engineering team's deliverables verifying all documented processes and procedures are followed. These procedures are based on enforceable national standards, client and industry best practices and are uniformly applied in system protection. Primary Responsibilities1. Prepares, executes and coordinates the planning, documentation and follow up of Cyber Asset assessments (CSVA, CSV), protective (security) patching and conducts reviews confirming engineering protection and control procedures are delivered.2. Able to work in a variety of functions either in field locations or in the home office, which may include necessary activities ensuring quality processes are implemented in optimization of system/component performance and availability. Verification of in field systems either documenting as left conditions or ensuring new systems meet requirements before in service.3. Applies industry best practices in development of procedures and processes addressing quality and reliability standards requirements. 4. Works effectively in a team environment and may assume the role of team leader.5. Provides quality assurance, procedure and standards requirements guidance and recommendations to other PPL employees in support of high quality, timely and cost-effective engineering solutions to technical problems. CIP audit guidance as required.6. Builds knowledge of the organization's reliability and quality procedures and processes.7. Ensures department deliverables exceed all industry standard requirements through development and implementation of uniform processes based on industry best practices. 8. Implement industry best practices in development of efficient review processes and procedure development. Basic Qualifications1. Bachelor's Degree in engineering or science from a college or university accredited by ABET. Candidates with extensive experience and certifications in quality assurance in lieu of the specified degree will be considered.2. Minimum 5 years experience implementing a quality or reliability program, or project management involving engineering projects.3. Engineers with quality or licensing experience with generation, distribution, industrial protection, or system planning will be considered.Preferred Qualifications (some of the following)1. NERC Reliability standards expertise Cybersecurity program implementation expertise.2. Knowledge of Protection & Controls engineering3. Six Sigma Certification4. PMP Certification5. Experience in the energy industry Quality program implementation in a regulated industry such as nuclear or pharmaceuticals.
ICS / MENSA project DUTIES & RESPONSIBILITIES: • Responsible for the delivery of agreed modules within a project (PLC, SCADA, Testing, Networking, Documentation, Hardware design etc) • Work as directed by the Senior/Lead Engineer and Project Manager • Responsible for meeting the technical and quality requirements of project • Ensure project adherence to company quality processes and procedures • Identify project opportunities and variations • Support the Project Manager in identifying and managing risks and issues • Identify and enable use of reusable modules by standardisation and modularization of systems where appropriate • Provide Health and Safety leadership by example • Develop project modules. (Modules as identified in the design – PLC code modules, SCADA, scripts, Mimics, comms drivers, etc.) • Report on progress of all assigned activities to Senior/Lead Engineer or Project Manager • Identify any deviations from agreed functionality or scope and notify Senior/Lead Engineer or Project Manager • Peer review documents created by the project team or other teams as required • Undertake site surveys as required • Support outline design, upfront design studies and requirement definition for clients • Develop FDS and DDS • Develop test specification & design testing methodology • Development of site work documentation (Risk assessment, method statement, site test documentation) • Develop O & M documentation • Undertake full integrated system testing, CFAT, SAT and installation • Undertake observations, variation and reworks as well as packing and shipping of the system • Undertake site installation and retesting • Provide warranty support as necessary QUALIFICATIONS & EXPERIENCE: • Experience of the full project life cycle from system specification through design, development, testing and on-site commissioning is essential • Hands on experience of PLC and SCADA systems • A good appreciation of Control panels, electrical installation and Instrumentation solutions • A Degree or HND/HNC in Electrical / Electronic Engineering, Control Systems or relevant discipline • Incorporated Engineer or working towards professional registration • Experience of some or all of the following is desirable:
Description:The Assistant Project Controls Specialist will support all aspects of project controls and reporting, including, project change management, cost control, progress measurement, schedule development and schedule control. Assist with developing, implementing and maintaining a cost management reporting data warehouse to produce valuable program controls reports and data. Perform project planning and scheduling tasks.Coordinate project schedules and assist with the development of scheduling reports.Coordinate project set-up in the Enterprise Planning & Controls software.Review data; maintain logs; and run reports in the Enterprise Planning & Controls software or other tools.Validate Work Breakdown Structure (WBS).Perform budget tracking against Purchase Orders or Subcontracts.Assist with upstream (prime contract) / downstream (PO & subcontract) change orders.Document changes to cost reports or forecasts.Assist with the development of a cash flow.Assist with the development of Level 1, Level 2, and Level 3 schedules.Complete schedules and diagrams in Microsoft Visio.Apply logic ties within the schedule.Document schedule progress.Perform resource loading of a schedule.Develop a earned value tracking document.Integrate data from one program to another.Assist quality checks and inspections on project controls deliverables.All other duties as assigned. Requirements: Bachelor's degree in Engineering, Construction Management or related field. Applicable experience may be substituted for the degree requirement.Experience with Oracle Primavera P6.Ability to work independently, think creatively and analytically, and make quick and sound decisions.Excellent written and verbal communication skills.Proficient with Microsoft Office.May be required to obtain an OSHA 10 hour safety certification.Willingness to accept long term field assignments
Power Systems Stability and Steady-State EngineerWe are seeking a talented and experienced Power Systems Stability and Steady-State Engineer to join our team. As a Power Systems Engineer, you will play a pivotal role in analyzing and enhancing the stability and steady-state performance of our power systems. The ideal candidate should possess significant experience in both stability and steady-state as they relate to power systems.Responsibilities:· Perform comprehensive stability analysis of power systems, including transient stability, voltage stability, and small signal stability assessments.· Conduct steady-state analysis, load flow studies, and power flow simulations to evaluate the performance of the power system under various operating conditions.· Identify potential stability and steady-state issues and provide recommendations for system improvements, control strategies, and operational enhancements.· Collaborate with the planning and operations teams to assess the impact of system changes, such as generation additions, load variations, and network expansions on stability and steady-state performance.· Utilize advanced stability and steady-state analysis software and tools to model and simulate complex power system networks accurately.· Investigate and troubleshoot stability and steady-state-related events, working closely with field personnel and control center operators.· Develop and implement stability control schemes, as well as steady-state control algorithms, to improve the overall dynamic and steady-state performance of the power system.· Stay updated with industry standards, emerging trends, and best practices related to power systems stability and steady-state analysis.· Participate in the testing and commissioning of new power system equipment and control systems to verify their stability and steady-state performance.· Prepare technical reports and documentation, presenting findings and recommendations to stakeholders.Requirements:· Bachelor's degree in Electrical Engineering or related field. A master's degree in Power Systems or a relevant discipline is preferred.· Extensive experience in stability and steady-state analysis as they relate to power systems, including transient stability, voltage stability, small signal stability, and power flow studies.· Proficiency in using industry-standard stability and steady-state analysis software such as PSS/E, PSCAD, PowerWorld, or DIgSILENT PowerFactory.· Strong understanding of power system dynamics, control systems, and protective relaying.· Familiarity with grid codes, regulations, and standards related to power systems stability and steady-state analysis.· Experience with dynamic modeling and simulation of power system components like generators, FACTS devices, and HVDC systems.· Solid analytical and problem-solving skills, with the ability to interpret simulation results and propose effective solutions.· Excellent communication and interpersonal skills to collaborate effectively with cross-functional teams and stakeholders.· Ability to work on multiple projects simultaneously and deliver results within defined timelines.· Professional engineering license or willingness to obtain one is a plus.Join our team and contribute your expertise in both stability and steady-state analysis to ensure the reliable and efficient operation of our power systems. If you are passionate about power systems and possess the required experience, we encourage you to apply for this challenging opportunity.
Control Room Operator | 3-Month Contract (Extension Likely) | Montrose, Scotland | RotationalPlease note this role is ROTATIONAL - 12.5 hour days with a mix of days and night shifts, 7 days on, 2 weeks off. Negotiable to 1 week on, 1 week off or 2 weeks on, 2 weeks off.Are you ready to be part of something big? We're seeking an experienced Control Room Operator to help us harness the power of the wind and contribute to a sustainable future.As a Control Room Operator, you'll play a pivotal role in the control and operation of a cutting-edge 1075MW offshore wind farm. You'll be the linchpin for safe and efficient wind turbine maintenance, remote alarm response, personnel coordination, and emergency management. In this role you'll be responsible for: The Monitoring and Controlling of the Wind Farm: Ensuring seamless wind farm operation and safety, adhering to policies and procedures, responding to alarms and coordinating offshore activities, including personnel and vessel transfers. Setting People to Work: Optimising wind farm availability by liaising with staff and contractors. Safety Rules Duties: Performing operational controller duties, ensuring safe release and return of wind turbine apparatus, and switching/controlling high voltage systems within safety guidelines. Marine Coordination: Coordinating vessel and transport movements in the offshore wind farm. Technical Support: Investigating technical incidents, notifying responsible parties, and providing timely energy trading forecasts. Ideally you'll have: Experience in WTSR, Operational Safety Rules, and can perform various authorised roles Experience in a control room environment with electrical focus; Experience with electrical system operations Working Knowledge of protection systems; Knowledge of HV safety rules, ideally with or working towards AP status; Experiences in use of SCADA, Network Control Systems, Trading Systems and Maintenance Management Systems. Some experience of working with vessels and marine control (advantageous but training will be given). If this sounds like something you'd be interested in, please apply!
Description:The Assistant Project Controls Specialist will support all aspects of project controls and reporting, including, project change management, cost control, progress measurement, schedule development and schedule control. Assist with developing, implementing and maintaining a cost management reporting data warehouse to produce valuable program controls reports and data. Perform project planning and scheduling tasks.Coordinate project schedules and assist with the development of scheduling reports.Coordinate project set-up in the Enterprise Planning & Controls software.Review data; maintain logs; and run reports in the Enterprise Planning & Controls software or other tools.Validate Work Breakdown Structure (WBS).Perform budget tracking against Purchase Orders or Subcontracts.Assist with upstream (prime contract) / downstream (PO & subcontract) change orders.Document changes to cost reports or forecasts.Assist with the development of a cash flow.Assist with the development of Level 1, Level 2, and Level 3 schedules.Complete schedules and diagrams in Microsoft Visio.Apply logic ties within the schedule.Document schedule progress.Perform resource loading of a schedule.Develop a earned value tracking document.Integrate data from one program to another.Assist quality checks and inspections on project controls deliverables.All other duties as assigned. Requirements: Bachelor's degree in Engineering, Construction Management or related field. Applicable experience may be substituted for the degree requirement.Experience with Oracle Primavera P6.Ability to work independently, think creatively and analytically, and make quick and sound decisions.Excellent written and verbal communication skills.Proficient with Microsoft Office.May be required to obtain an OSHA 10 hour safety certification.Willingness to accept long term field assignments